| |
The astounding results achieved in
Toolgal Test Centre
10,000, cuts !!!
Material: hard metal Ø12 mm
Advance rate F: 13 mm/min
Cutting speed VC: 18 m/sec
Wheel size: Ø150 x 1.3 mm
Cooling oil viscosity: 400/ 6.5st
Working parameters:C.N.C work centre.
Wheel was stabilized between two Ø110 flanges,
work material was firmly set. |
 |
| Diamond Cut-Off Wheels |
 |
HARD METAL - RM501 D126 C100
|
catalog number for order |
| D |
U-X |
centrebore H20 |
centrebore H22 |
centrebore H30 |
centrebore H31.75 |
| 1A1R 75 |
1.1x6 |
WT005207 |
|
|
WT005212 |
| 1A1R 125 |
1.1x6 |
WT005208 |
|
|
WT005213 |
| 1A1R 150 |
1.1x6 |
WT005209 |
|
|
WT005214 |
| 1A1R 175 |
1.3x7 |
WT005210 |
|
|
WT005215 |
| 1A1R 200 |
1.3x7 |
WT005211 |
WT005217 |
WT005218 |
WT005216 |
| 1A1R 200 |
1.3x10 |
|
WT004859 |
|
|
| CBN Cut-Off Wheels |
|
HSS - RM901 B126 V210
|
catalog number for order |
| D |
U-X |
centrebore H20 |
centrebore H22 |
centrebore H30 |
centrebore H31.75 |
| 1A1R 75 |
1.1x6 |
WT005224 |
|
|
WT005229 |
| 1A1R 125 |
1.1x6 |
WT005225 |
|
|
WT005230 |
| 1A1R 150 |
1.1x6 |
WT005226 |
|
|
WT005231 |
| 1A1R 175 |
1.3x7 |
WT005227 |
|
|
WT005232 |
| 1A1R 200 |
1.3x7 |
WT005227 |
WT005234 |
WT005235 |
WT005233 |
|
| |
| Work Recommendations |
| 1. |
Work piece must be firmly set with minimum
protrudence to avoid vibrations.
|
| 2. |
The wheel must be set between max.
size flanges without interfering with work.
|
| 3. |
Make sure there is no side or peripheral run-out.
|
| 4. |
Higher advance rate will shorten the wheel life,
work with the best advantage rate to suit your needs. |
|
 |
|
| |
|
| |
| Applications for CBN
Cut-Off Wheels
|
 |
Slicing HSS round bars. |
|
Cutting HSS flat plates at various thicknesses.
|
|
Cutting HSS finger milling tools
|
|
Grooving. |
|
| |
|
| |
| Applications for Diamond
Cut-Off Wheels
|
|
Slicing of hard metal round bars. |
|
Cutting hard metal finger milling tools. |
|
Cutting off hard metal blocks of various thickness. |
|
| |
| Recommended work conditions |
|
|
| Diamond Hardmetal |
| RM 501 |
| D126 C100 |
|
F=13-50 mm/min
VC=18-22 m/s |
|
|
| CBN H.S.S |
| RM 901 |
| B126 V210 |
|
F=13-50 mm/min
VC=28-32 m/s |
|
|
|
diameter and thickness must be taken into consideration. |
|
fit to wet cut only. |
|
|
| |
 |
